Re: [HPDD-discuss] Lustre System buffer usage and OST striping

On Jan 19, 2015, at 9:59 AM, Patrick Farrell <paf(a)cray.com&gt; wrote: John, This is at a little bit of a tangent to your questions (which make for very interesting reading), but is IOZone single threaded, and have you considered OSS caching as well? Cray observed a situation a bit like this, but with OSS caching, not client caching. (I'm omitting any explanation of how we ruled out client caching here; you'll have to trust me this effect was depending on OSS memory.) A multi-threaded write, then read of data sets slightly larger than available memory (IE, data written/read per OSS slightly exceeded memory per OSS). We'd expect something like a full LRU 'end around', where all the data is evicted from cache without being used. We used some debugging code to track the progress of each thread within the file it was reading. In fact, what we saw was that - due to apparent raciness on the client - some threads would get slightly ahead of others, then suddenly leap ahead, dramatically pulling away from the other threads and finishing quickly. It appeared as though those threads got far enough ahead that they reached the portion of their data still in cache on the OSS (since as they read in data, they evicted data from *all* the files/threads, not just their own.) The last few threads, which never 'jumped', appeared, by their progress rate, to be forced to read everything from disk. That may or may not be relevant here. As an interesting aside, we noticed that the large performance improvements in 2.6 significantly reduced the raciness of progress between multiple threads on the same node... Which, bizarrely, had the impact in the pathological case described above (write-then-read slightly more than available memory) of reducing performance. The progress of the threads was much more orderly and even between the different threads, which resulted in something closer to the full 'end-around' cache flush on the read operations. (In general, 2.6 is much faster, outside of this pathological case. ) - Patrick > On 01/19/2015 07:59 AM, John Bauer wrote: > Andreas > > Thank you for the reply. This investigation started with the observation of slow backwards reads of file by an MSC.Nastran run doing > a Lanczos eigenvalue solve ( see image below ). I point that out so it is known that I am not investigating an academic run of iozone. > It is far simpiler to work with iozone than MSC.Nastran. > > If you care to read a bit more to see the observed behavior of Lustre, please read on. > > The following image depicts the access of the file over time, by the iozone run. What is quite odd is that when the second backward read of the file begins, > the reading of the file is at its fastest(steep slope) during this backwards read. This is at at time when all of the end of the file should have been LRU'd out of the system buffers by the previous backwards read. The rate then slows down through the meat of the file and then starts getting faster again toward the end of the second backwards read. > > I have run this job many times and the behavior, as depicted in the first image, is always the same. The slopes vary some, but there is always this > serpentine look to it. It is not the same OST's every time. If I run this with iozone using 256K requests, the slopes for the backwards reads gets much lower. > To me, it seems at though something is wrong with the LRU mechanism. Note in the last image, when iozone is using 256k requests, that this behavior starts during the > forward reads of the file. It is not just a backward read phenomenon. It happens every time when reading backwards. Only occasionally during the forward reads. > > John > > <mime-attachment.png> > > <mime-attachment.png> > > <mime-attachment.png> > > > <mime-attachment.png> > > <mime-attachment.png> > > <mime-attachment.png> > >> On 1/18/2015 10:29 PM, Dilger, Andreas wrote: >> On Jan 18, 2015, at 17:19, John Bauer <bauerj@iodoctors.com<mailto:bauerj@iodoctors.com>> wrote: >> >> I have been observing what I would think is unexpected behavior. I will try to keep this short, and start with the question. >> >> Should it be expected, when sequentially reading a striped file multiple times, that the data from some OST's remains in the system cache >> while others does not? >> >> This isn't something that I'm aware of myself, nor something I'd necessarily expect. That said, this isn't actually a bad thing. >> >> File is 80GB is size. >> System has 64GB of memory. >> File is striped 16 way, 1MB stripe size. Application is iozone. >> File is written forwards twice, then read forwards twice, then read backwards twice. >> >> There is 80GB / 16 stripes = 5GB of data per stripe. If the pages were handled in strict LRU order, then one would expect the two forward reads to blow out the cache, and result in 10GB of data read per stripe. Then, the first backwards read would access most of the data from cache, maybe 60GB taking into account the OS, so 80GB - 60GB = 20GB read on the first pass (1.25GB/stripe), and another full 5GB for the second backward read. That gives 16.25GB/stripe in the expected LRU case. >> >> That you got 16-17GB read on many OSCs is expected. For the OSCs that had less read i checked that the cached reads sum(16Gb - actual read) = 45GB or so, so it doesn't exceed the amount that could have been cached. >> >> I don't know why this might have happened, but there could be several causes. If one of the LDLM locks was cancelled due to memory pressure, it would have allowed some data to stay in cache for the first backward read, and by being accessed more than once it wouldn't fall off the LRU for the second backward read. >> >> Cheers, Andreas >> >> Application request size is 1MB. >> Run on the swan cluster at Cray, Inc. lustre-cray_ari_s/2.5_3.0.101_0.31.1_1.0502.8394.10.1-1.0502.17198.8.51 >> >> The file is large enough to oversubscribe the system's memory. I would expect that each OST would see uniform activity. >> But that is far from the case. Here is the amount of data read by each OST during the entire iozone job, ranges from 10G to 17G. >> <afcjgffc.png> >> >> When I look at how much data the OST's have read versus time, some have no activity during the entire 2nd backwards read. >> The OST's that have the low amount of data read also have very high application data delivery rates during these same periods, indicating the data is in the system cache. >> Is this to be expected? >> >> Thanks >> >> John >> >> >> >> _______________________________________________ >> HPDD-discuss mailing list >> HPDD-discuss@lists.01.org<mailto:HPDD-discuss@lists.01.org> >> https://lists.01.org/mailman/listinfo/hpdd-discuss >> > > > > _______________________________________________ > HPDD-discuss mailing list > HPDD-discuss(a)lists.01.org > https://lists.01.org/mailman/listinfo/hpdd-discuss _______________________________________________ HPDD-discuss mailing list HPDD-discuss(a)lists.01.org https://lists.01.org/mailman/listinfo/hpdd-discuss