6:27 a.m.
I’ve identified the problematic commit:
http://review.whamcloud.com/#/c/12961/
LU-5919<https://jira.hpdd.intel.com/browse/LU-5919> build: Make "make
rpms" use "make srpm" output
Hash: a71ab04971382c77f708d6a082e8ee2fa845e9be
I haven’t dug in to this in detail yet, but that commit is the culprit. That commit
breaks the build process described here:
https://wiki.hpdd.intel.com/display/PUB/Building+Lustre+from+Source
Resulting in the error described earlier in this thread:
error: line 144: Version required: Requires: kernel =
Hmmmm… I’ll see what I can figure out.
- Patrick Farrell
From: Patrick Farrell <paf@cray.com<mailto:paf@cray.com>>
Date: Friday, June 5, 2015 at 3:20 PM
To: Sean Caron <scaron@umich.edu<mailto:scaron@umich.edu>>, Stephen Champion
<schamp@sgi.com<mailto:schamp@sgi.com>>
Cc: "hpdd-discuss@lists.01.org<mailto:hpdd-discuss@lists.01.org>"
<hpdd-discuss@lists.01.org<mailto:hpdd-discuss@lists.01.org>>
Subject: Re: [HPDD-discuss] Performing "make rpms" on current Git pull fails
with "error: line 144: Version required: Requires: kernel ="
I've hit this as well. Some relatively recent commit - 2.7.0 is fine - has broken
this process. I tried to figure out what and gave up, I am now bisecting. The specific
issue seems to be that %kversion is not being read out, but I'm not sure of the why.
- Patrick Farrell
________________________________
From: HPDD-discuss
[hpdd-discuss-bounces@lists.01.org<mailto:hpdd-discuss-bounces@lists.01.org>] on
behalf of Sean Caron [scaron@umich.edu<mailto:scaron@umich.edu>]
Sent: Friday, June 05, 2015 3:01 PM
To: Stephen Champion; Sean Caron
Cc: hpdd-discuss@lists.01.org<mailto:hpdd-discuss@lists.01.org>
Subject: Re: [HPDD-discuss] Performing "make rpms" on current Git pull fails
with "error: line 144: Version required: Requires: kernel ="
Sorry for the confusion; that was a typo in my e-mail trying to copy and paste from my
log; every time I've run that ./configure I did actually get the leading slash in
there:
[build@lustre-mgs lustre-release]$ history | grep configure
70 ./configure
--with-linux=/home/build/kernel/rpmbuild/BUILD/kernel-3.10.0_229.4.2.el7.centos_lustre.x86_64/
72 ./configure
--with-linux=/home/build/kernel/rpmbuild/BUILD/kernel-3.10.0_229.4.2.el7.centos_lustre.x86_64/
97 ./configure
--with-linux=/home/build/kernel/rpmbuild/BUILD/kernel-3.10.0_229.4.2.el7.centos_lustre.x86_64/
122 history | grep configure
[build@lustre-mgs lustre-release]$
I've tried a few "make clean" and retry attempts and I reach the same end;
the make completes with no errors, but "make rpms" fails with that line 144
error.
I looked at the page Richard sent me and I don't see any material changes from section
30.2.2 on in the administrator's guide; there's a few extra packages in there that
aren't mentioned in my printing of the Lustre 2.x operations manual ... but I never
hit any errors previous in the build process; the kernel builds fine ... just trying to
build the Lustre RPMs fails ... final step ... I feel like anything I would have made a
hash of so grievously would have caused fatal errors earlier in the process, no?
Best,
Sean
On Fri, Jun 5, 2015 at 3:49 PM, Stephen Champion
<schamp@sgi.com<mailto:schamp@sgi.com>> wrote:
On 6/5/2015 12:41 PM, Sean Caron wrote:
I've been following the build directions explicitly from section 30.2.2 on only
correcting for differences between CentOS 7 and RHEL 7 ... everything built clean until
now, as far as I can tell. At what point in the build process would I have gone awry for
that to happen?
At configure.
Right at momentary freeze as my mail client was sending, I saw the problem.
./configure
--with-linux=home/build/kernel/rpmbuild/BUILD/kernel-3.10.0_229.4.2.el7.centos_lustre.x86_64/
the leading slash is missing.